機械進氣系統介紹翻譯-世聯翻譯
Unitrans世聯
| 進氣系統翻譯屬于機械翻譯領域，世聯北京翻譯公司擅長各種機械翻譯，我們有專業的機械翻譯團隊處理此類稿子，以下就是本公司專業機械翻譯人員翻譯整理的有關機械進氣系統介紹。 進氣系統 翻譯：Air intake system 進氣系統由空氣濾清器、壓氣機、中冷器和各種連接用成型鋼管、膠管等組成。 翻譯：The air intake system consists of the air filter, blower, intercooler, and various forming pipes and rubber hoses for connection. 空氣濾清器應該采用干式空濾器，不能使用油浴式空濾器。 翻譯：The air filter should be of the dry type instead of the oil-bath type. 4100QBZL型增壓中冷柴油機的空氣濾清器流量≥600m33/h，阻力≤2.4kPa。空氣濾清器的安裝位置應距離排氣管和增壓器 500mm以上。進氣管路的內徑不得小于Φ60mm，保證內壁清潔、光滑，而且管路系統各連接處不允許漏氣；聯接的膠管應采用內襯鋼絲膠管，以免氣流高速流動時膠管被吸扁而使進氣不足、功率下降、冒煙嚴重且導致增壓器壓氣機端漏機油。 翻譯：Turbo Intercooler Diesel Engine 4100QBZL is equipped with an air filter with the flow ≥600m3/h and the resistance ≤2.4kPa. The air filter should be so positioned that it is away from the exhaust pipe and turbocharger by more than 500mm. The air intake pipe ID should be no thinner than Φ60mm. The interior wall should be clean and smooth. No air leakage is acceptable at any connection in the pipe system. The connecting rubber hoses should be internally lined with steel wire; otherwise, the fast flowing air could transform the hoses into "flat strips", resulting in insufficient air intake, reduced power, serious smoke emission, and oil leakage on the turbo blower end. 進氣管路從空氣濾清器出氣口到壓氣機進氣口之間的進氣真空度≤4kPa，整個進氣系統最大阻力≤6kPa，盡量避免使用有安全濾芯的空氣濾清器，以減少進氣阻力。 翻譯：The air intake vacuum in the air intake pipe from the air filter outlet to the blower inlet is ≤4kPa, and the maximum resistance of the entire air intake system is ≤6kPa. To minimize the air intake resistance, avoid using an air filter with a safety element wherever possible. 進氣系統進氣口應高于地面 2m 并設置防雨裝置，空氣濾清器進氣口處應設網狀初級過濾較大的異物。管路聯接時不允許有小于 90°的急轉彎，而且轉彎盡可能不多于兩處，轉彎半徑應大于管子直徑的 3 倍，整個進氣管路應盡可能短，盡量減少進氣的摩擦損失。 翻譯：The air intake port of the air intake system should be 2m above the floor and should be equipped with a rain protector. The air intake port of the air filter should be equipped with a strainer to filter massive foreign articles preliminarily. No elbow sharper than 90° is acceptable while connecting the pipes. In addition, no more than two elbows are permitted. The elbow radius should be larger than 3 times of the pipe diameter. The entire air intake pipe should be as short as possible to minimize the frictional loss of the air intake. 如果您喲機械翻譯相關服務需求，可以隨時與本公司在線客服人員聯系，同時也可以撥打我們的服務熱線：010-64809262http://www.unitrans.cn世聯北京翻譯公司竭誠為您提供最優質的翻譯服務。 |
